Fitspresso Reviews – Does It...
How it Works2 mins ago
Cooks: Knife Sharpening
14 Answers
Asking about knives and sharpeners, and Melv recommended a Robert Welch Santoku 14cm knife, which seems to meet all the criteria.
I'm a bit puzzled because on the Robert Welch site they recommend you buy/use THIS type of sharpener:
https:/
which is a handheld job with a ceramic wheel against which you pull your knife blade.
You'd have thought they would have recommended one of their steels, but no.
Anyone use one of these type of sharpeners, and are they useful?
Ta
BB
I'm a bit puzzled because on the Robert Welch site they recommend you buy/use THIS type of sharpener:
https:/
which is a handheld job with a ceramic wheel against which you pull your knife blade.
You'd have thought they would have recommended one of their steels, but no.
Anyone use one of these type of sharpeners, and are they useful?
Ta
BB
Answers
1 to 14 of 14
Best Answer
No best answer has yet been selected by bainbrig. Once a best answer has been selected, it will be shown here.
For more on marking an answer as the "Best Answer", please visit our FAQ.
Just personal experience, but I've tried many many different types of knife sharpener, including those dual grinding stone types.
I desperately want the easier alternatives to be effective, but I've never found that they work as well as the more traditional approach favoured by danny.
Personally, I don't use an oil stone, but a series different grades of diamond stones every few months to remove a lot of metal at a relatively fine angle to the blade.
Every time I pick a knife from the drawer, before using it, I touch it up with two or three swipes on a steel (which could be a diamond steel, a ceramic steel or a conventional steel). The steel is used at a coarser angle to the blade so that it skims off a tiny amount of metal, but restores the blade to it's very sharp state.
I desperately want the easier alternatives to be effective, but I've never found that they work as well as the more traditional approach favoured by danny.
Personally, I don't use an oil stone, but a series different grades of diamond stones every few months to remove a lot of metal at a relatively fine angle to the blade.
Every time I pick a knife from the drawer, before using it, I touch it up with two or three swipes on a steel (which could be a diamond steel, a ceramic steel or a conventional steel). The steel is used at a coarser angle to the blade so that it skims off a tiny amount of metal, but restores the blade to it's very sharp state.
Re:oilstone
The language surrounding so called oilstones is very misleading. First off, there’s no such thing as an “oilstone.” Long ago, these abrasive stones were simply called whetstones. “Whetting” was the period word for “sharpening” and it had nothing to do with applying liquid to a rock. Nor is oil required for their use. All “oilstones” can be used successfully with water (or soapy water). And oil, spit or water can be used inter- changeably on all whetstones (including synthetic stones). So what is this thing we call an “oilstone?”
There are two basic types of sharpening stones: synthetic stones and naturally quarried stones. All sharpening stones – including waterstones – have more in common than they have differences. All are basically made of some sort of ceramic.
The ceramic grit in man-made waterstones, the white ceramic stones and Norton’s “India” stones are all aluminum oxide, just like your grinding wheel. Of course, you know that each of these products cuts quite differently. The reason lies not with the actual ceramic cutting particle, but with the matrix that binds the crystals together.
Waterstones have soft clay-like binders which give up their particles, allowing them to roll over to expose new sharp facets and new crystals. India stones have harder matrices that make them to wear longer and cut more slowly.
Natural stones are typically some form of quartz (which is also a ceramic) such as Novaculite. Arguably the best source of these stones is the Ouachita Mountains in Arkansas. But Novaculite is found elsewhere, including in naturally occurring Japanese waterstones. Folks in the 18th century were getting Novaculite-rich stones from what is today Syria, Lebanon and Israel. These modern-day nations were then part of the Ottoman- Turkish Empire, which is where people in the Anglo-American 18th-century world got the term “Turkey Stone.”
There are a few other popular synthetic grits such as silicon carbide (a.k.a. carborundom), Norton’s dark gray coarse stones, and zirconium oxide, which is often mixed with aluminum oxide and sold as “Norzon” for belt sander belts (a useful substitute for a diamond plate). These particles are so hard that their matrices typically can’t hold them together well, so products made from these ceramics work quickly and quickly wear out.
It is the matrix – not the grit – that I think should be important to you; it should be the determining factor in your choice of stones. If you are working broad, flat surfaces, stones with a softer matrix will be better for you. If you are honing small tools, or small surfaces of large tools (such as curved edges), you’ll probably do better with stones that have a harder matrix.
You should never “lubricate” your stones. Lubrication reduces friction and that reduces the cutting efficiency of your
stone. “Cutting fluids,” such as those used in machine shops, are used to carry away heat and swarf (little bits of metal). So maybe “cutting fluid” is a better term for the stuff we spritz on our stones. Here’s how it works:
Stones, like your skin, are porous. Bits of swarf can get trapped in the pores of a stone, just like dirt gets trapped in the pores of your skin. As it builds up, the tool will begin to ride on the swarf instead of on the crystals. When that happens, we say our stone is “clogged.” At that point, it will cut slowly. What we need is a liquid with a low enough surface tension to get into the pores and lift out (through surface tension) the stuff we don’t want there. Soap reduces the surface tension of water and allows it to flow into the pores of our skin. You can use soap (any kind will work) as a cutting fluid. I mix up dish detergent with water in a plant sprayer. The ratio of water to soap is determined by the porosity of the stones. (Technically, each different grit stone would be most efficient with a different fluid.
Oil has a low surface tension and makes an excellent cutting fluid. But there is no one best oil for a
The language surrounding so called oilstones is very misleading. First off, there’s no such thing as an “oilstone.” Long ago, these abrasive stones were simply called whetstones. “Whetting” was the period word for “sharpening” and it had nothing to do with applying liquid to a rock. Nor is oil required for their use. All “oilstones” can be used successfully with water (or soapy water). And oil, spit or water can be used inter- changeably on all whetstones (including synthetic stones). So what is this thing we call an “oilstone?”
There are two basic types of sharpening stones: synthetic stones and naturally quarried stones. All sharpening stones – including waterstones – have more in common than they have differences. All are basically made of some sort of ceramic.
The ceramic grit in man-made waterstones, the white ceramic stones and Norton’s “India” stones are all aluminum oxide, just like your grinding wheel. Of course, you know that each of these products cuts quite differently. The reason lies not with the actual ceramic cutting particle, but with the matrix that binds the crystals together.
Waterstones have soft clay-like binders which give up their particles, allowing them to roll over to expose new sharp facets and new crystals. India stones have harder matrices that make them to wear longer and cut more slowly.
Natural stones are typically some form of quartz (which is also a ceramic) such as Novaculite. Arguably the best source of these stones is the Ouachita Mountains in Arkansas. But Novaculite is found elsewhere, including in naturally occurring Japanese waterstones. Folks in the 18th century were getting Novaculite-rich stones from what is today Syria, Lebanon and Israel. These modern-day nations were then part of the Ottoman- Turkish Empire, which is where people in the Anglo-American 18th-century world got the term “Turkey Stone.”
There are a few other popular synthetic grits such as silicon carbide (a.k.a. carborundom), Norton’s dark gray coarse stones, and zirconium oxide, which is often mixed with aluminum oxide and sold as “Norzon” for belt sander belts (a useful substitute for a diamond plate). These particles are so hard that their matrices typically can’t hold them together well, so products made from these ceramics work quickly and quickly wear out.
It is the matrix – not the grit – that I think should be important to you; it should be the determining factor in your choice of stones. If you are working broad, flat surfaces, stones with a softer matrix will be better for you. If you are honing small tools, or small surfaces of large tools (such as curved edges), you’ll probably do better with stones that have a harder matrix.
You should never “lubricate” your stones. Lubrication reduces friction and that reduces the cutting efficiency of your
stone. “Cutting fluids,” such as those used in machine shops, are used to carry away heat and swarf (little bits of metal). So maybe “cutting fluid” is a better term for the stuff we spritz on our stones. Here’s how it works:
Stones, like your skin, are porous. Bits of swarf can get trapped in the pores of a stone, just like dirt gets trapped in the pores of your skin. As it builds up, the tool will begin to ride on the swarf instead of on the crystals. When that happens, we say our stone is “clogged.” At that point, it will cut slowly. What we need is a liquid with a low enough surface tension to get into the pores and lift out (through surface tension) the stuff we don’t want there. Soap reduces the surface tension of water and allows it to flow into the pores of our skin. You can use soap (any kind will work) as a cutting fluid. I mix up dish detergent with water in a plant sprayer. The ratio of water to soap is determined by the porosity of the stones. (Technically, each different grit stone would be most efficient with a different fluid.
Oil has a low surface tension and makes an excellent cutting fluid. But there is no one best oil for a
Link here as I was confused with the term “oilstone”
https:/
https:/
I have a kitchen devils sharpener similar to the one in your link brainbig but it didn't cost £30 more like less than £10. It does a great job on my sabatier, ikea, cheapo knives, so much so I'm always slicing bits of my fingers off!!
Personally, unless I was a trained chef, I wouldn't bother with fancy expensive steels or sharpeners when you can buy very efficient ones for a far more reasonable price.
I sharpen my knives every time I use them & I think that's important.
Personally, unless I was a trained chef, I wouldn't bother with fancy expensive steels or sharpeners when you can buy very efficient ones for a far more reasonable price.
I sharpen my knives every time I use them & I think that's important.
-- answer removed --
1 to 14 of 14
Related Questions
Sorry, we can't find any related questions. Try using the search bar at the top of the page to search for some keywords, or choose a topic and submit your own question.